Browse Categories
Browse by Manufacturer
Search
FOR FREE TECHNICAL ASSISTANCE CALL 1-800-950-9431 TO SPEAK TO A TECHNICIAN
Star Handpieces: 
INSTALLATION OF TURBINES FOR STAR HANDPIECES
  1. REMOVE THE END CAP
  2. CLEAN OUT THE HANDPIECE HEAD USING A COTTON SWAB, MAKE  SURE ALL DEBRIS IS REMOVED
  3. CLEAN OUT THE END CAP USING A COTTON SWAB MAKING SURE ALL DEBRIS IS REMOVED ( YOU CAN USE ALCOHOL, LUBRICANT, OR HANDPIECE CLEANER TO HELP WITH THE CLEANING PROCESS )
  4. PUSH THE TURBINE INTO THE END CAP MAKING SURE THE REAR GREEN O-RING IS SEATED COMPLETELY AND PROPERLY.  YOU SHOULD NO LONG BE ABLE TO SEE THE GREEN O-RING AND THE END CAP SHOULD STAY ON THE REAR BEARING BY ITSELF.
  5. HOLDING THE HANDPIECE WITH THE OPENING FOR THE TURBINE POINTING DOWN, INSERT THE TURBINE UP INTO THE HEAD AND SCREW ON THE END CAP.
  6. CONNECT THE HANDPIECE TO YOUR CONTROL UNIT AND RUN FOR 30 SECONDS. THE TURBINE MAY RUN SLOW AT FIRST AS THE GREASE IS DISTRIBUTED THROUGHOUT THE BEARINGS.



Kavo Handpieces

INSTALLATION OF TURBINES FOR KAVO HANDPIECES
  1. REMOVE END CAP
  2. REMOVE O-RING FROM THE HEAD OF THE HANDPIECE
  3. REMOVE O-RING FROM THE END CAP
  4. CLEAN OUT THE HEAD USING A COTTON SWAB MAKING SURE ALL DEBRIS IS REMOVED ( YOU CAN USE ALCOHOL, LUBRICANT, OR HANDPIECE CLEANER TO HELP WITH THE CLEANING PROCESS )
  5. CLEAN OUT END CAP USING A COTTON SWAB MAKING SURE ALL DEBRIS IS REMOVED
  6. INSTALL ONE O-RING IN THE HEAD OF THE HANDPIECE USING A DENTAL EXPLORER OR THE WOOD HANDLE OF A COTTON SWAB
  7. INSTALL THE REMAINING O-RING IN THE END CAP USING A DENTAL EXPLORER OR THE WOOD HANDLE OF A COTTON SWAB
  8. PUSH THE TURBINE INTO THE HEAD OF THE HANDPIECE USING A GENTLE ROCKING MOTION, IF NEEDED, TO FULLY SEAT THE TURBINE IN THE FRONT O-RING
  9. SCREW THE END CAP ON
  10. LUBRICATE TURBINE AND RUN FOR AT LEAST 30 SECONDS TO FLUSH OUT EXCESS LUBRICANT.



Midwest Tradition

INSTALLATION OF TURBINES FOR MIDWEST TRADITION HANDPIECES
  1. REMOVE END CAP
  2. REMOVE O-RING FROM THE HEAD OF THE HANDPIECE
  3. REMOVE O-RING FROM THE END CAP
  4. CLEAN OUT THE HEAD USING A COTTON SWAB MAKING SURE ALL DEBRIS IS REMOVED ( YOU CAN USE ALCOHOL, LUBRICANT, OR HANDPIECE CLEANER TO HELP WITH THE CLEANING PROCESS )
  5. CLEAN OUT END CAP USING A COTTON SWAB MAKING SURE ALL DEBRIS IS REMOVED
  6. INSTALL THE GREEN O-RING IN THE END CAP
  7. INSTALL THE BLUE O-RING ON THE FRONT FLANGED BEARING OF THE TURBINE
  8. PUSH THE TURBINE INTO THE END CAP USING A GENTLE ROCKING MOTION IF NEEDED 
  9. INSERT THE TURBINE INTO THE HEAD OF THE HANDPIECE AND SCREW THE END CAP ON
  10. LUBRICATE TURBINE AND RUN FOR AT LEAST 30 SECONDS TO FLUSH OUT EXCESS LUBRICANT


Midwest Quiet Air

INSTALLATION OF TURBINES FOR MIDWEST QUIET AIR HANDPIECES
  1. REMOVE END CAP
  2. REMOVE O-RING FROM THE HEAD OF THE HANDPIECE
  3. REMOVE O-RING FROM THE END CAP
  4. REMOVE OLD SPRING WASHER
  5. REMOVE OLD PRESSURE PLATE ( POWER LEVER MODELS ONLY )
  6. CLEAN OUT THE HEAD USING A COTTON SWAB MAKING SURE ALL DEBRIS IS REMOVED ( YOU CAN USE ALCOHOL, LUBRICANT, OR HANDPIECE CLEANER TO HELP WITH THE CLEANING PROCESS )
  7. CLEAN OUT END CAP USING A COTTON SWAB MAKING SURE ALL DEBRIS IS REMOVED
  8. INSTALL THE GREEN O-RING IN THE END CAP
  9. INSTALL THE NEW PRESSURE PLATE WITH THE RIDGE FACING UP ( POWER LEVER MODELS ONLY )
  10. INSTALL THE NEW SPRING WASHER
  11. PUSH THE TURBINE INTO THE END CAP USING A GENTLE ROCKING MOTION IF NEEDED
  12. INSTALL THE TURBINE INTO THE HEAD OF THE HANDPIECE, BE CAREFUL NOT TO MOVE THE SPRING WASHER OR IT CAN BIND ON THE FRONT BEARING
  13. SCREW THE END CAP ON
  14. LUBRICATE TURBINE AND RUN FOR AT LEAST 30 SECONDS TO FLUSH OUT EXCESS LUBRICANT


W&H Handpieces

INSTALLATION OF TURBINES FOR W&H HANDPIECES
   
1.       Remove end cap
2.       Remove old o-ring from the end cap ( we recommend using a dental explorer )
3.       Remove old turbine from the handpiece head ( make sure the whole turbine comes out, it should look
          like the new turbine you purchased ) 

4.       Remove old o-ring from the handpiece head
5.       Remove the white Teflon washer and brass spring washer noting how they are placed in the head
6.       Clean handpiece head and end cap with a cotton swab
7.       We recommend re-using the white Teflon washer that was in the handpiece head, if needed you can
          replace it with the new white Teflon washer supplied.

8.       Replace the brass spring washer in the head of the handpiece with the supplied brass spring washer
9.       Re-install the white Teflon washer and brass spring washer
10.     Install the new o-rings in the handpiece head and end cap
11.    Install the new turbine into the handpiece head, use a gentle rocking motion to ‘seat’ the turbine fully
          into the head
12.    Re-install the end cap and tighten
 
 
 
If you have any questions please call or e-mail us and we can walk you through the process. 
Thank You!!



Midwest, Kavo, NSK, Bien Air, W&H, Healthco, Lares, Micro Motors and Star are registered tradenames.  The original manufacturers do not endorse aftermarket products.
Mailing Lists
There are no mailing lists at this time.
Shopping Cart
Your cart is empty.